ProDino MKR Zero Ethernet V1

If you find faster, modern and powerful Arduino board with Ethernet connection, a ProDino MKR Zero Ethernet V1 board is for you. You can do with it vary applications, it could be from home projects to industrial use. It also as a great educational tool for learning about 32-bit application development. The board is powered by Atmel’s SAMD21 MCU, which features a 32-bit ARM Cortex® M0+ core and W5500 Ethernet chip.

ProDino MKR Zero Ethernet V1 top

Communication


Are you developing projects for an environment where wireless connections are unavailable or would be inefficient? The ProDino MKR Zero Ethernet V1 allows you to have a wired Ethernet connection between your board and Internet. This is particularly important for projects that has to be installed in industrial environments with either electromagnetic noise or special safety requirements. It contains all futures on ProDino MKR Zero board plus Ethernet W5500 chip.

ProDino MKR Zero Ethernet V1 accent

The ProDino MKR Zero Ethernet V1 has 4 relays. The 4 Relays are a solution for driving high power loads that cannot be controlled by microcontroller’s digital IOs, due to the current and voltage limits of the controller. Each relay provides 2 pole changeover contacts (NO and NC). Relays are useful in switching on/off AC appliances like fan, light, motor or high current DC actuators like solenoid valve etc. Included four LEDs indicate the on/off state of each relay.

ProDino MKR GSM Ethernet V1 without cover

The 4 digital inputs are isolated. This is helpful for connecting ProDino MKR Zero Ethernet V1 to a system with a different ground and different voltage or noisy system. This electrically isolates a controller from the high-power system by use of an opto-isolator IC. This allows the low-voltage side to control a high voltage side. Great for use in noisy circuits where signal lines require electrical isolation. Four LEDs indicate the On/Off state of each input.

ProDino MKR Zero V1 inputs

Inputs

ProDino MKR Zero V1 outputs

Outputs

The ProDino MKR Zero Ethernet V1 board contains one GROVE Digital connector. The Grove System simplifies traditional electronics it consists of a base platform and various modules with standardized connectors. Each Grove module addresses a range of functions such as simple LEDs, buttons, switches to complex servo control, etc. With the combination with Grove modules, the project possibilities are endless!

ProDino MKR Zero Ethernet V1 board 3D
RS485

Thanks that the ProDino MKR Zero Ethernet board owns RS485, now you will be able to have a communication port for your RS485 devices! It will allow up to 32 devices to communicate through the same data line over a cable length of up to 1200m/4000ft. It is and the ultimate expansion that allows your board to connect to almost every legacy industrial system using serial connectivity such as industrial PLCs, controllers, drives and HMIs. 

The RS485 can be use to turn old industrial systems like industrial machinery, heating systems and conveyors into new IoT devices. It supports high speed 500 Kbps in a short distance.

The ProDino MKR Zero Ethernet contains more a micro USB connector and a reset button.
It is compatible with "Arduino MKR GSM 1400".

Getting started


You can find in the Tutorial section all the information you need to configure your board, use the Arduino Software (IDE), and start tinker with coding and electronics. What you can do with this board see in our Examples.

Features 


  • ATSAMD21G18 Microprocessor, 32-Bit ARM Cortex® M0+
  • check
    W5500 Ethernet chip
  • check
    1 x GROVE connector
  • check
    4 Relays Output
  • check
    Pluggable connectors
  • check
    4 Optical Isolated Inputs 
  • check
    RS485 port 
  • check
    Switching Regulators power supply
  • check
    Arduino MKR GSM1400 compatible

Specification


  • check
    mP, DC Current per I/O Pin 7 mA
  • check
    Clock speed 48 MHz  
  • check
    SRAM 32 KB
  • check
    256 KB Flash Memory
  • check
    Ethernet 802.3 10/100 Mbit/s
  • check
    RS485 speed 500 Kbps (short distance)
  • check
    Optical isolated digital Inputs: 4 (working voltage 3-30 V, On arrives form 3 V)
  • check
    Relay outputs: 4 (maximum voltage/current 250V/5A)
  • check
    Input Voltage: (Vin) 8 - 30 V
  • check
    Dimension: 70 mm X 92 mm X 32 mm
  • check
    Weight: 132 g
ProDino MKR Zero Ethernet V1 board front

Additional connectors


J10 Grove Digital (External)

ProDino WiFi GROVE
  • 1  GROVE_D0 - Primary digital Input/Output D12_I2C_SCL
  • 2  GROVE_D1 - Primary digital Input/Output D11_I2C_SDA
  • 3  Vcc  - Grove module powers 3,3 V
  • 4  GND  - Ground

J14 (internal)

ProDino MKR Zero V1 J14 connector diagram
  • 1  5V
  • 2  GND
  • caret-right
    3  3.3V
  • caret-right
    4  GSM_CTS
  • caret-right
    5  GSM_RTS
  • caret-right
    6  GSM_RX
  • 7  GSM_TX
  • 8  GSM_DTR
  • caret-right
    9  GSM_RESETN
  • caret-right
    10  ADC_VBAT
  • caret-right
    11  PMIC_IRQ

What does the board consume?


Voltage

All relays off

All relays on

8 V

0.075 A

0.270 A

12 V

0.050 A

0.195 A

24 V

0.028 A

0.095 A

Isolated inputs when On state

1.5 V - 0.3 mA

5 V - 0.6 mA

12 V - 1.0 mA

24 V - 1.5 mA

Other devices from the series


Datasteets