USB RS485
Isolated Converter V3

KMP USB RS485 Isolated Converter V3.0 3D

Thanks our KMP USB RS485 Isolated Converter V3.0, now you will be able to have a communication with RS485 devices through the USB port on your computer. It will allow up to 128 devices to communicate through the same data line over a cable length of up to 1200m/4000ft. It is and the ultimate expansion that allows you connect to almost every legacy industrial system using serial connectivity such as industrial PLCs, controllers, drives and HMIs. The RS485 can be used to turn old industrial systems like industrial machinery, heating systems and conveyors into new IoT devices.

The converter is equipped with 2.75 kV of isolation and internal surge-protection on each data lines to protect the host computer and converter against high voltage spikes, as well as ground potential difference. A USB RS485 Isolated Converter V3.0 also features a high-speed 500 Kbps transmission rate, and supports various O.S. It Includes by RS485 line galvanically isolated power supplier.

KMP USB RS485 Isolated Converter V3.0 Top

Features


  • check
    USB interface: Fully compliant with V1.0, 2.0 specifications
  • check
    Powered by: FTDI FT231X
  • check
    Power supplies from USB port, no external power is needed
  • check
    Power supply for RS485 line is galvanically isolated
  • Converter gets 1 COM port in the system when it is connected
  • check
    Unique device ID number
  • check
    Device supplied: pre-programmed with unique USB serial number
  • check
    RS485 line protection: Against surge, short circuit, and voltage peak
  • check
    Compatible with Modbus RTU/ASCII and DMX protocols
  • check
    Up to 128 nodes in network configuration
  • check
    TX/RX mode LED indicators
  • check
    Plugable RS485 connector
  • check
    Entire USB protocol handled on the converter. No USB specific firmware programming required
KMP USB RS485 Isolated Converter V3.0 RS485 Terminal

Specifications


  • check
    RS485 Data transfer rates: from 300 baud to 500 Kbaud
  • check
    512 byte receive buffer and 512 byte transmit buffer
  • check
    Data Format: Asynchronous data with all common combination of bits, parity, stop.
  • check
    UART interface support: for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity
  • check
    Adjustable latency timer: 1 to 255 msec
  • check
    Adjustable read and write timeouts: 0 to 10000 msec
  • check
    Transmission distance: RS485 Up to 4000ft (1200M)
  • check
    ESD Protection: 35 kV
  • check
    Isolation voltage: 2.75 kV
  • check
    Operating environment: -20 to 50° C
  • check
    Storage temperature: -20 to 70° C
  • check
    Humidity: 10-90% non-condensing.
  • check
    Dimension: 86 mm X 43 mm X 20 mm
  • check
    Weight: 37 g.
KMP USB RS485 Isolated Converter V3.0 USB B Connector
KMP USB RS485 Isolated Converter V3.0 Left-Back

How to connect the USB RS485
converter with existing line


You can connect your KMP USB RS485 Isolated Converter V3.0 direct to existing RS485 line (the line ends are terminated with resistors 120 Ohm and the line is powered). In this case you must use A, B and GND lines.

KMP USB RS485 Isolated Converter V3.0 connects with existing line

Connecting the USB RS485
converter with new line


You can connect your KMP USB RS485 Isolated Converter V3.0 at the beginning RS485 line. And you can power the RS485 line with converter. It include galvanically isolated DC-DC power converter. In this case you must use A, B, V+ and GND lines. Resistors R1* and R3* (are depending at the line [you might use 560 Ohm]) for powering and 2x 120 Ohm for termination line.

KMP USB RS485 Isolated Converter V3.0 new line